Assignment 3 Camera Simulation

Name

Date submitted: 8 May 2006

Code emailed: 8 May 2006

Compound Lens Simulator

Description of implementation approach and comments

A lens file is represented in the LensSystem class, which in turn is represented by a vector of lenses. Each lens is a struct containing the 4 values from the file as well as min and max value along the z axis where the lens is "valid" (this is calculated based on the radius of the lens and the aperture of the actual lens element).

In order to calculate a ray lens interface intersection, I created a sphere based on which way the lens was "facing", and performed a ray sphere intersection. For the aperture, I used a ray plane intersection.

I chose to have the film plane start at z = 0 and have the ray travel along the positive z axis. Lens elements are lined up accordingly. I use ConcentricSampleDisk to sample on the entire back face of the back lens, and trace the rays through the stack. Weighting returned is the (A/Z2) * (cos4 theta) given in the paper unless the ray is blocked in which case it is 0. While tracing the lens, I noticed some lens elements with refraction index of 0 (like the aperture), I just assumed that the space behind the aperture was air, and used 1 instead (for all 0's).

Final Images Rendered with 512 samples per pixel

My Implementation

Reference

Telephoto

hw3telephoto_512

Double Gausss

hw3dgauss_512

Wide Angle

hw3wide_512

Fisheye

hw3fisheye_512

Final Images Rendered with 4 samples per pixel

My Implementation

Reference

Telephoto

hw3telephoto_4

Double Gausss

hw3dgauss_4

Wide Angle

hw3wide_4

Fisheye

hw3fisheye_4

Experiment with Exposure

Image with aperture full open

Image with half radius aperture

Observation and Explanation

Render a second image of the scene using the double gauss lens with the aperature radius reduced by one half. What effect to you expect to see? Does your camera simulation produce this result? When you half the aperture size, you have decreased the photograph exposure by how many stops?

With a smaller aperture, the amount of light that gets to the image plane is also reduced. As a result the image is darker (as demonstrated in the image). Halfing the aperture is equivalent to stopping down 2 stops.

Autofocus Simulation

Description of implementation approach and comments

I used the Modified Laplacian described in the Nayer paper as a measure of how focused the image was. For the intensity of a pixel, I just used the sum of the RGB values. As the autofocus regions weren't very large, I simply calclated the MLP for the entire autofocus region (rather than do windows of 3 or 5 pixels). I used a step size of one in the mlp calculation, and this seemed to work pretty well.

I began by first calculating the focal distance of the lens system and beginning my search there. This makes sense because in a real camera system, the film plane must be behind the focal point. This method had several positive side effects. 1) I could avoid most of the high SML values that occur when the film distance is less than the focal distance. 2) I could speed up my search by not searching all those values.

Calculating the focal distance was somewhat annoying as it required tracing rays from objects space into the lens (opposite of the way we were doing in part 1). But by doing shooting rays with direction (0,0,1) through the system and then calculating the intersection of the resulting ray with the z axis, I could determine the focal distance.

The search proceeded from filmDist = focalDist in somewhat large steps along the filmDist (the constant FILMSTEP -- set to 4 in my implementation) and searches for a peak. A peak is defined here as 3 adjcaent MLP values where the middle one is larger than both its left and right neighbors. Using this initial algorithm, I encountered many false positives, as the MLP values had many little humps. Fortunately, the focused peak was always significantly larger than the unfocused one (and also very thin). So in order to avoid false positives, I found the ratio of the peak with its two neighbors. The ratio of the 2 neighbors to the peak must be less than a certain threshhold value in order for me to accept it as the actual focuses point. So peaks that were too close in magnitude to its neighbors were discarded. This makes sense given that the peaks are very large and very sharp.

Then given this range (from lower neighbor to upper neighbor), I perform another search over the smaller range (with step SMALLSTEP -- set to 0.3) to get a more accurate filmDist that produces the sharpest image. I use a similar search to the one above, searching for a peak. However, even in such a small range there are false positives, so I still use a threshold value for the ratio of the peak to its neighbors. I can be conservative in my approach (avoid false positives at all costs), because I also keep a maxSML value which tracks the maximum in the range. So if no peak is found which satisfies the threshold, the true peak is still found because it will be the max value in the range.

Final Images Rendered with 512 samples per pixel

Adjusted film distance

My Implementation

Reference

Double Gausss 1

62.1 mm (61.6mm when using SMALLSTEP = 0.1)

hw3afdgauss_closeup

Double Gausss 2

39.7 mm (39.9mm when using SMALLSTEP=0.1)

hw3afdgauss_bg

Telephoto

117.1 mm (117.0mm when using SMALLSTEP = 0.1)

hw3aftelephoto

Note: The images were rendered with SMALLSTEP = 0.3, but I set it smaller to try and get the more exact focal lengths)

Any Extras

Stopped down by 4

Exposure * 4 in PhotoShop

Reference

Decreasing the aperture by 4 stops is equivalent to dividing the radius by 4 (because one stop divides the radius by sqrt(2)). There are actually quite a few differences in the image other than just the darkening. Once noticible thing is that the picture is much granier, this is due to far fewer rays actually making it to the image plane. Secondly, the depth of field is greatly increased with a small aperture. If you look carefully, you can see that the stuff in the foreground and background are a lot more in focus than in the original image.

Update: I've also uploaded the same image with the exposure quadrupled in photoshop as well as the original image. You can clearly see the increased graininess as well as the significantly increased depth of field when compared to the original.